Misters cut water use in drought

Every dust control plan uses water because it is inexpensive, easy to obtain, and safe for the environment.

Water usage for sprinklers, hoses, and mist

Atomized mist dust cannons use more than 20 times less water than comparable industrial sprinklers.

Except when it isn’t.

Debilitating droughts are currently swallowing many areas of the world. In South America, the government of Brazil is advising citizens to prepare for the worst as they endure what is being called the most severe drought in their history.

In the United States, the State of California faces yet another year of intense drought and operators are forced to navigate through often conflicting air pollution and water conservation directives. And as rushing through showers, allowing lawns to go brown, and entertaining thoughts of drinking recycled sewage water are among the least of citizen’s concerns, they see industry appearing to dump drinkable water on dirt.

Suddenly, the neighbors whom operators sought to protect from dust emissions are taking a closer look at dust suppression methods. Even the use of recycled water cannot settle the controversy due to additional pollution concerns.

Drought not only forces water conservation, but makes dust more of a problem. There is no silver bullet for this heated issue. However, some methods of suppression use more water than others and that could amount to millions of gallons saved.

Atomized mist dust suppression

For decades, dust suppression meant industrial sprinklers or a person standing around holding a fire hose.

One is made for irrigation and the other putting out fires.

And they are really good at what they were designed to do: providing maximum water flow.

Both methods can wet surfaces to prevent dust, but they use a lot more water than is necessary. And their water droplet size is too large to capture airborne dust.

You can set out to save money and end up spending more in the long run. Even in times of adequate rainfall, less is always more.

Fire hose dust suppression

Less water means:

  • More strategic water usage and lower associated cost.
  • Reduced storm water effects and runoff, critical in keeping air and land pollution in balance.
  • Fewer pools of water to ensure a safer and more efficient worksite.
  • Avoided product oversaturation, often creating a muck that is difficult to handle and sticks to facility surfaces and equipment, shortening the life of both.

Atomized mist dust cannons were developed specifically with dust suppression in mind, using just the amount of water that is necessary to wet surfaces and bring airborne dust particles to the ground.

How much water can be saved?

To illustrate this, let’s compare atomized mist to the other two methods, as well as a heavy rainstorm to add a familiar perspective.

All methods can be adjusted to give different output based on need.

water-conservation

For this comparison, we’ll use the popular DustBoss 60 (DB-60) mist cannon, named so because the range is 60 meters (200 feet). We are comparing this to a sprinkler model with similar coverage area and a 1.5 inch fire hose, which is the size that feeds the DB-60.

This industrial sprinkler can run about 500 GPM (1,893 LPM), making it the worst in terms of water usage. That is more than 21 times more water than the DB-60 at 23 GPM (88 LPM).

The fire hose works at 100 gallons per minute (GPM) (378 LPM), more than four times more water than the DB-60.

Conserving even more with surfactants

Surfactants can be metered into atomized mist using a dosing pump, increasing the water’s potency against fugitive dust and stretching out water usage even further.

Surfactants, short for surface-acting agents, can be added to the water to improve the wetting characteristics of water. We often say it makes the water wetter, making it easier for the droplet to collide with the dust particle by lowering the drop’s surface tensions.

What does a surfactant do?

Think about water on a smooth surface, such as raindrops on a window. Water on a smooth surface will usually form a bead with strong walls. That is surface tensions that prevents the walls from collapsing.

Water treated with surfactants create a flatter bead. Weaker surface tensions mean weaker walls, less able to support a structure. And weaker walls mean more collisions. Surfactants just make water more effective at airborne suppression.

Surfactants can help make a smaller amount of water go further, but as with any chemicals or additives, you always need to pay special attention to the environmental impact and runoff – and impact to product.

Need help balancing clean air and water conservation?

Every site is different. Tell us about your operation so we can recommend the right system.

Request site analysis
Sending
This entry was posted in News, Product Information. Bookmark the permalink. Both comments and trackbacks are currently closed.